kylendm
Well-known member
Well it's been a while since I actually hoped on this board. I figured I'd try stop in and say Hi.
Lately I've been jamming with my Baron Custom Amps for the last few months.
Here's what I've done with them.
First up is my Snott Watt.
Here's some specs.
Basically it sits on my desk and I do line out recordings. It's cool because when you plug a cable in the Line In a dummy load kicks so you don't need to be plugged into a cab. Actually you can't have both in at the same time haha.
It's quite flashy too.
http://www.youtube.com/watch?v=lgidfJUCWhU
http://www.youtube.com/watch?v=Hr3bcyxvQrw
http://dl.dropbox.com/u/3602793/New%20Snott%20of%20Sharyn.mp3
Basically it's the most brutal low wattage high gain amp out there.
-------------------------------------------------------------------
Next is my Baron Custom Amps K88.
Probably the best high gain amp i've ever played.
It's 100 watts has two lead channels and a clean channel.
The Lead channel has two channels in it, A and B. A has a little less gain than B. So you can essentially have one as a lead boost but I like my A channel to be low on gain and the other to be very full of it.
I use a Mesa Stiletto 4x12 with it and it's just killer.
http://dl.dropbox.com/u/3602793/ROS.mp3
http://dl.dropbox.com/u/3602793/Heavy.mp3
http://www.netmusicians.org/files/42-Baron.mp3
---------------------------------------------------------------------------
I just wanted to post some stuff mainly because I miss this place. Always thought everyone here was very cool and helpful.
Once the E2 comes out I'll be right back. I'm sure I still have a good years wait but until then I'll be jamming with these buddies. :lol:
Lately I've been jamming with my Baron Custom Amps for the last few months.
Here's what I've done with them.
First up is my Snott Watt.
Here's some specs.
Code:
-Single channel dual gain mode 12BH7 Push/Pull 5 to 7 watt amplifier.
-100% Tube signal path No Diodes or SS components
-3-12AX7A preamp tubes and 1 12BH7 push/Pull power tube.
-Vintage Gain Mode: Clean to crunch.
-Modern Gain Mode: Crunch to Metal
-Dual gain Controls, Treble boost, gain modes, dry/wet settings.
-Dummy load for use as a preamp and or line out.
-Designed by Carl Williams of Anchovy Amplifiers and David Woodhouse
Basically it sits on my desk and I do line out recordings. It's cool because when you plug a cable in the Line In a dummy load kicks so you don't need to be plugged into a cab. Actually you can't have both in at the same time haha.
It's quite flashy too.
http://www.youtube.com/watch?v=lgidfJUCWhU
http://www.youtube.com/watch?v=Hr3bcyxvQrw
http://dl.dropbox.com/u/3602793/New%20Snott%20of%20Sharyn.mp3
Basically it's the most brutal low wattage high gain amp out there.
-------------------------------------------------------------------
Next is my Baron Custom Amps K88.
Probably the best high gain amp i've ever played.
It's 100 watts has two lead channels and a clean channel.
The Lead channel has two channels in it, A and B. A has a little less gain than B. So you can essentially have one as a lead boost but I like my A channel to be low on gain and the other to be very full of it.
I use a Mesa Stiletto 4x12 with it and it's just killer.
http://dl.dropbox.com/u/3602793/ROS.mp3
http://dl.dropbox.com/u/3602793/Heavy.mp3
http://www.netmusicians.org/files/42-Baron.mp3
---------------------------------------------------------------------------
I just wanted to post some stuff mainly because I miss this place. Always thought everyone here was very cool and helpful.
Once the E2 comes out I'll be right back. I'm sure I still have a good years wait but until then I'll be jamming with these buddies. :lol: