Need help! Routing a rm4 a rm50, g-major, maxon od808, Tuner

[elpresidente99]

Hello my friends!!

At first please excuse my English!

I`m a complete newbie in routing amps i need your helb. I want to route a rm4 and a rm50 and a g-major to habe access to all channels and effects.

ROuter is a voodoo lab GRX and a ground controll.

For example FS:1 = chanel one on the rm50
FS:2 = chanel two on the rm4
FS:3 = chanel four on the rm4 with Delay from the g-major.

Is this feasable?? IF not then i sell the g-major and buy analog delays and reverbs because i use only a few things of the g-major.

Ok.

I tried to draw such a routing but i have many problems with the right in's and outs.

Here is the Picture:
Picture

I hope this is right to combinate the rm 4 and the rm50.

It would be very nice if somebody can draw me a right routing on such a working sheet.

http://www.voodoolab.com/gcxdiagrams/blank_gcx_worksheet_l.pdf

Greetz and thanks

 

[SacredGroove]

Hey man, I can work on it for you, but it'll have to be tomorrow. Your diagram is close, though.

 

[elpresidente99]

OK i think now i have it. Is this a right routing to include all my stuff.

here is the Picture.
Picture


THe only thing i don't now is which output i take from the rm4 to the loop2 in.

Is ther maybe an other way with less cables or something else.

Thanks

 

[Raf_666]

OK i think now i have it. Is this a right routing to include all my stuff.

here is the Picture.
Picture


THe only thing i don't now is which output i take from the rm4 to the loop2 in.

Is ther maybe an other way with less cables or something else.

Thanks

Hey you should use the pre loop out connection ...

Raf

 

[SacredGroove]

Hope this works for you.
--Loop 2 switches between amps. Whenever loops 2-4 are on, the RM4 is active with G-Major and vice versa for the RM50.
--If you don't want FX on RM4 then switch loops 3, 4 off. If you don't want FX on RM50 then switch loops 3, 4 on.
--Set the G-Major to KillDry when using the parallel loops.

Do you have the Ground Control Pro or the original?

 

[elpresidente99]

Can you explain what you have done because i cant understand this.

loop1: on/off od808
Loop2: on rm over the rm50 /off only rm50

For example:

Loop 1 on, loop 2 on, loop3 off, loop4 off

Od808 is on then the rm4 plays. Right??


Example two

Loop 1 off, loop 2 on, loop3 on, loop4 on

THe rm4 plays plus the G-major is on. right??


Example three

Loop 1 on, loop 2 off, loop3 off, loop4 on

Odd 808 is on the rm 50 is on but no tone in cause of the Loop 4on. Right??

That means for i can't play the rm50 without the g-major is this right??

Thanks

 

[SacredGroove]

I edited my previous post. Check it out. You seem to understand it fine. I'm sure it can still be modified, too.

 

[elpresidente99]

but the G-major ist everytime in the signal of the rm50 right??

I don't understand one thing if loop3 and loop4 off. the signal goes in the rm50 in and then out by the send fx but get no return, is there any tone??

Thanks

 

[SacredGroove]

If you want the RM50 by itself then loops 3 or 4 or both have to be on in order block the FX from going in and out of the parallel loop. The RM50 input will go directly to the poweramp and to the speaker outputs.

 

[elpresidente99]

Aha this means if you send somthing from the send fx but there will be no return so the signal goes directly to the poweramp and there is a tone???

Greetz

 

[SacredGroove]

Yep, check it out and see how it works.